 |
Checking the chain drive oil level
|
|
|
|
1. Stand the scooter on a level surface.
NOTE:
Л Place the scooter on a suitable stand.
Л Make sure that the scooter up right.
М Remove:
chain drive case cover 1
3 - 43
CHECKING THE CHAIN DRIVE OIL LEVEL/
CHANGING THE CHAIN DRIVE OIL
CHK
ADJ
Н Remove:
chain drive oil filler cap 1
О Check:
chain drive oil level
Wipe the dipstick clean, insert it into the oil filler hole (without screw it in), and then remove it to check the oil level.
The chain drive oil level should be between the minimum level mark a and maximum
level mark b.
Below the minimum level mark → Add the recommended chain drive oil to the proper level.
Recommended chain drive oil SAE 80 API GL-4 Hypoid gear oil
П Install:
chain drive oil filler cap
chain drive case cover
T.
R.
7 Nm (0.7 m · kg, 5.1 ft · lb)
CHANGING THE CHAIN DRIVE OIL
Р Place a container under the chain drive.
Р Remove:
chain drive case cover
chain drive oil filler cap
chain drive oil drain bolt 1
Completely drain the chain drive of its oil.
Р Check:
drain bolt gasket Damage → Replace.
Р Install:
chain drive oil drain bolt
T.
R.
20 Nm (2.0 m · kg, 14 ft · lb)
3 - 44
CHK
CHECKING THE CHAIN DRIVE OIL LEVEL ADJ
С Fill:
chain drive oil
(with the specified amount of the recom-mended chain drive oil)
Quantity
L (0.62 Imp qt, 0.74 US qt)
Т Check:
chain drive oil level
Refer to “CHECKING THE CHAIN DRIVE OIL LEVEL”.
3 - 45
ADJUSTING THE REAR BRAKE LOCK LEVER CABLE
CHASSIS
CHK
ADJ
ADJUSTING THE REAR BRAKE LOCK
LEVER CABLE
WARNING
Do not use the rear brake lock lever while driving.
NOTE:
У Place the scooter on the centerstand.
У Before adjusting the rear brake lock lever, check the rear brake fluid level.
Ф Measure:
rear brake lock lever cable length a Out of specification → Adjust.
Rear brake lock lever cable length 45 ~ 47 mm (1.77 ~ 1.85 in)
10 Adjust:
rear brake lock lever cable length
▼▼▼▼▼▼▼▼▼▼▼ ▼▼▼▼▼▼▼▼▼ ▼▼▼▼▼▼▼▼▼▼▼▼
И Slowly apply the rear brake several times.
И Turn the adjusting nut 1 until rear brake lock lever cable length a is 42 ~ 44 mm (1.65 ~ 1.73 in) with the rear brake lock lever released.
|
|
|
И Set the rear brake lock lever, wait more than 5 minutes, and then release the rear brake lock lever.
И Turn the adjusting nut 1 until rear brake lock lever cable length a is 45 ~ 47mm (1.77 ~ 1.85 in) with the rear brake lock lever released.
| Directionb | Rear brake lock lever | |
| cable length increased. | ||
| Directionc | Rear brake lock lever | |
| cable length decreased. | ||
▲▲▲▲▲▲▲▲▲▲▲ ▲▲▲▲▲▲▲▲▲ ▲▲▲▲▲▲▲▲▲▲▲▲
3 - 46
CHK
CHECKING THE BRAKE FLUID LEVEL ADJ
И
Й
EAS00116
CHECKING THE BRAKE FLUID LEVEL
1. Stand the scooter on a level surface.
NOTE:
Й Place the scooter on a suitable stand.
Й Make sure that the scooter is upright.
К Check:
brake fluid level
Below the minimum level mark a → Add the recommended brake fluid to the proper level.
Recommended brake fluid
DOT 4
И Front brake Й Rear brake
WARNING
Л Use only the designated brake fluid. Other brake fluids may cause the rubber seals to deteriorate, causing leakage and poor brake performance.
Л Refill with the same type of brake fluid that is already in the system. Mixing brake fluids may result in a harmful chemical reaction, leading to poor brake performance.
Л When refilling, be careful that water does not enter the reservoir. Water will signifi-cantly lower the boiling point of the brake fluid and could cause vapor lock.
CAUTION:
Brake fluid may damage painted surfaces and plastic parts. Therefore, always clean up any spilt brake fluid immediately.
NOTE:
In order to ensure a correct reading of the brake fluid level, make sure that the top of the reservoir is horizontal.
3 - 47
CHECKING THE BRAKE PADS/
CHECKING THE BRAKE HOSES
CHK
ADJ
| CHECKING THE BRAKE PADS | ||
| И | ||
| The following procedure applies to all of the | ||
| brake pads. | ||
| 1. Operate the brake. | ||
| 2. Check: | ||
| • front brake pad | ||
| Wear indicator groove 1 almost disap- | ||
| peared → Replace the brake pads as a set. | ||
| Refer to “FRONT AND REAR BRAKES” in | ||
| chapter 4. | ||
| • rear brake pad | ||
| Й | ||
| Wear indicator 2 almost touch the brake | ||
| disc → Replace the brake pads as a set. | ||
| Refer to “FRONT AND REAR BRAKES” in | ||
| chapter 4. |
|
|
|
