 |
L (3.17 Imp qt, 3.81 US qt) Without oil filter cartridge replacement
|
|
|
|
А L (2.46 Imp qt, 2.96 US qt) With oil filter cartridge replace-ment
А L (2.55 Imp qt, 3.07 US qt)
Х Install:
engine oil filler cap
10.Start the engine, warm it up for several min-utes, and then turn it off.
11.Check:
Ц engine
(for engine oil leaks)
12.Check:
Ч engine oil level
Refer to “CHECKING THE ENGINE OIL LEVEL”.
13.Reset:
• engine oil change indicator light
▼▼▼▼▼▼▼▼▼▼▼ ▼▼▼▼▼▼▼▼▼ ▼▼▼▼▼▼▼▼▼▼▼▼
Ш Turn the key to “ON”.
Ш Hold the “OIL CHANGE” button 1 pushed for two to eight seconds.
Ш Release the “OIL CHANGE” button 1, and the oil change indicator light will go off.
NOTE:
If the engine oil is changed before the oil change indicator light comes on (i.e. before the periodic oil change interval has been reached), the indicator light must be reset after the oil change for the next periodic oil change to be indicated at the correct time. To reset the oil change indicator light before the periodic oil change interval has been reached, follow the above procedure, but note that the indicator light will come on for 1.4 seconds after releas-ing the “OIL CHANGE” button, otherwise repeat the procedure.
▲▲▲▲▲▲▲▲▲▲▲ ▲▲▲▲▲▲▲▲▲ ▲▲▲▲▲▲▲▲▲▲▲▲
3 - 32
MEASURING THE ENGINE OIL PRESSURE
EAS00077
CHK
ADJ
MEASURING THE ENGINE OIL PRESSURE
Ъ Check:
engine oil level
Below the minimum level mark → Add the recommended engine oil to the proper level.
Ъ Remove:
left lower side cover mole
Refer to “SIDE COVER MOULDINGS AND
LEG SHIELD”.
Ъ Start the engine, warm it up for several min-utes, and then turn it off.
CAUTION:
When the engine is cold, the engine oil will have a higher viscosity, causing the engine oil pressure to increase. Therefore, be sure to measure the engine oil pressure after warming up the engine.
Ы Remove:
main gallery plug 1
O-ring
WARNING
The engine, muffler and engine oil are extremely hot.
Ь Install:
pressure gauge 1
oil pressure adapter B 2
Pressure gauge 90890-03153
Oil pressure adapter B 90890-03124
3 - 33
MEASURING THE ENGINE OIL PRESSURE/
CLEANING THE AIR FILTER ELEMENT
6. Measure:
|
|
|
• engine oil pressure
CHK
ADJ
(at the following conditions) Out of specification → Replace.
Engine oil pressure
150 kPa (1.50 kg/cm2, 21.8 psi) at 1,200 r/min
Engine oil temperature 70 °C (158 °F)
Engine oil pressure Possible causes
Faulty oil pump Clogged oil filter
Below specification Leaking oil passage Broken or damaged oil seal
Leaking oil passage
Above specification Faulty oil filter Oil viscosity too
High
Э Install:
O-ring New
main gallery plug
T.
R.
12 Nm (1.2 m · kg, 8.7 ft · lb)
Ю Install:
left lower side cover mole
Refer to “SIDE COVER MOULDINGS AND
LEG SHIELD”.
CLEANING THE AIR FILTER ELEMENT
А Remove:
front cowling upper cover
windshield
front cowling inner panel Refer to “FRONT COWLING”.
А Remove:
air filter case cover 1
air filter element
А Clean:
air filter element
Apply compressed air to the outer surface of the air filter element.
А Check:
air filter element Damage → Replace.
3 - 34
CLEANING THE AIR FILTER ELEMENT/
CLEANING THE V-BELT CASE AIR FILTER ELEMENT
5. Install:
• air filter element
• air filter case cover
CAUTION:
CHK
ADJ
Never operate the engine without the air fil-ter element installed. Unfiltered air will cause rapid wear of engine parts and may damage the engine. Operating the engine without the air filter element will also affect the carburetor tuning, leading to poor engine performance and possible overheat-ing.
NOTE:
When installing the air filter element into the air filter case cover, be sure their sealing surfaces are aligned to prevent any air leaks.
Б Install:
front cowling inner panel
windshield
front cowling upper cover Refer to “FRONT COWLING”.
CLEANING THE V-BELT CASE AIR FILTER
ELEMENT
Л Remove:
left upper side cover mole
left footrest board
Refer to “SIDE COVER MOULDINGS AND
LEG SHIELD”.
Л Remove:
V-belt case cover 2 1
V-belt case air filter cover 2
3 - 35
CHK
CLEANING THE V-BELT CASE AIR FILTER ELEMENT ADJ
3. Remove:
• V-belt case air filter element (left) 1
• V-belt case air filter element (right) 2
4. Clean:
• V-belt case air filter element
Apply compressed air to the inner surface of V-belt case air filter element.
5. Check:
• V-belt case air filter element Damage → Replace.
CAUTION:
|
|
|
