Главная | Обратная связь
МегаЛекции

МегаЛекции: Разное

WHAT CRITICISMS CAN BE LEVELLED AGAINST MODERN DIPLOMACY VEHICLE IDENTIFICATION NUMBER Valve spring free length (intake and exhaust) Valve spring compressor 90890-04019, YM-04019 Un tour de France fantastique Un printemps qui ne venait pas To reset the oil change indicator light To prevent sparking, ground all spark plug leads before cranking the engine. To prevent damage to the cylinder head, camshafts or camshaft caps, loosen the camshaft cap bolts in stages and in a criss-cross pattern, working from the outside in. The throttle body should not be disassem-bled. The rear brake will not function properly if the connections are reversed. The ignition system fails to operate (no spark or intermittent spark). The camshaft cap bolts must be tightened evenly or damage to the cylinder head, camshaft cap, and camshafts will result. The Bramble Bush by Ch. Mergendahl The brake master cylinder reservoirs SYNCHRONIZING THE THROTTLE BODIES STARTING FAILURE/HARD STARTING STARTING CIRCUIT CUT-OFF SYSTEM OPERATION (XP500) Start switch ON: less than 1 V Since the V-belt case air filter element is a dry type, do not let grease or water contact it. SIDE COVER MOULDINGS AND LEG SHIELD SELF-DIAGNOSIS MALFUNCTION CODES Securely support the vehicle so that there is no danger of it falling over. Securely support the scooter so that there is no danger of it falling over. REMOVING THE FRONT WHEEL (XP500) REMOVING THE A.C. MAGNETO ROTOR Read the title of the following text. What can this text deal with? Decide if the following statements are true or false. Read the text and check. Radiator cap tester adapter 90890-01352, YU-33984 Put in the adjective from the first sentences into the second sentence in its correct form . Proper brake hose routing is essential to insure safe scooter operation. Refer to “CABLE ROUTING” in chapter 2. Pour ou contre remplacer les fournitures par des ordinateurs ? Piston ring side clearance Top ring PERIODIC MAINTENANCE AND LUBRICATION CHART OUTLINE OF ANTI-LOCK BRAKE SYSTEM (XP500A) Minimum brake pad thickness 0.8 mm (0.03 in) Minimum brake disc thickness Maximum secondary shaft runout 0.08 mm (0.0031 in) Make sure there are no foreign materials in the wheel hub. Foreign materials cause damage to the inner sensor rotor and front wheel sensor. Make sure that the main switch is set to “OFF” before checking the operation of the hydraulic unit. La galette des rois est les autres L (3.17 Imp qt, 3.81 US qt) Without oil filter cartridge replacement Karrimor Оркнейских 65 рюкзак International situation in the Far East in the early 20th century was determined by Intake air temperature sensor resistance INSTRUMENT FUNCTION Multi-function display INSTALLING THE HYDRAULIC UNIT INSTALLING THE CRANKSHAFT MAIN Inner-rotor-to-outer-rotor-tip clearance III. Персональные обязанности заместителей командира (и отдельных офицеров) HEADLIGHT DOES NOT COME ON TURN SIGNAL DOES NOT COME ON HANDLING THE REAR SHOCK ABSORBER Give Russian equivalents of the following words and phrases. Try to memorize them. FRONT BRAKE MASTER CYLINDER FRONT BRAKE MASTER CYLINDER Fork seal driver weight 90890-01367, YM-A5142-4 ECU (engine) SELF-DIAGNOSTIC FUNCTION ECU (ABS) AND FAIL-SAFE RELAY (XP500A) Do not touch the handlebar grip until the rubber adhesive has fully dried. Do not spin the bearing with compressed air because this will damage the bearing surfaces. 9 глава Do not spin the bearing with compressed air because this will damage the bearing surfaces. 8 глава Do not spin the bearing with compressed air because this will damage the bearing surfaces. 7 глава Do not spin the bearing with compressed air because this will damage the bearing surfaces. 6 глава Do not spin the bearing with compressed air because this will damage the bearing surfaces. 5 глава Do not spin the bearing with compressed air because this will damage the bearing surfaces. 4 глава Do not spin the bearing with compressed air because this will damage the bearing surfaces. 3 глава Do not spin the bearing with compressed air because this will damage the bearing surfaces. 2 глава Do not spin the bearing with compressed air because this will damage the bearing surfaces. 19 глава Do not spin the bearing with compressed air because this will damage the bearing surfaces. 18 глава Do not spin the bearing with compressed air because this will damage the bearing surfaces. 17 глава Do not spin the bearing with compressed air because this will damage the bearing surfaces. 16 глава Do not spin the bearing with compressed air because this will damage the bearing surfaces. 15 глава Do not spin the bearing with compressed air because this will damage the bearing surfaces. 14 глава Do not spin the bearing with compressed air because this will damage the bearing surfaces. 13 глава Do not spin the bearing with compressed air because this will damage the bearing surfaces. 12 глава Do not spin the bearing with compressed air because this will damage the bearing surfaces. 11 глава Do not spin the bearing with compressed air because this will damage the bearing surfaces. 10 глава Do not spin the bearing with compressed air because this will damage the bearing surfaces. 1 глава Do not allow grease to contact the V-belt, primary and secondary pulleys. DISASSEMBLING THE WATER PUMP DISASSEMBLING THE PRIMARY SHEAVE DISASSEMBLING THE FRONT FORK LEGS DISASSEMBLING THE FRONT BRAKE Digital circuit tester 90890-03174 Damaged cable sheaths may cause the cable to corrode and interfere with its movement. Replace damaged cable sheaths and cables as soon as possible. D. The radiator fan motor fails to turn. CHECKING THE STARTER MOTOR CHECKING THE IMMOBILIZER SYSTEM CHECKING THE EXHAUST GAS AT IDLE CHECKING THE CRANKSHAFT AND CHECKING THE COOLING SYSTEM CHECKING THE CONDITION OF THE CHECKING THE CLUTCH PLATES CHECKING THE CHAIN DRIVE OIL LEVEL Charging method using a constant voltage charger Brake pad wear limit 0.8 mm (0.03 in) Brake force and vehicle stability Basic troubleshooting instructions B. What type of heating is pictured? Fill in the scheme with the correct words from the text and fill in the table below. AT THE UN FRENCH SLIPS AND ENGLISH STANDS TALL Any of the following fail to light: turn signal light, brake light or an indicator light. Any of the following fail to light: head-light, high beam indicator light, taillight, licence plate light, storage box light, aux-iliary lights or meter light. After adjusting the throttle cable free play, turn the handlebar to the right and to the left to ensure that this does not cause the engine idling speed to change. ADJUSTING THE VALVE CLEARANCE ADJUSTING THE REAR WHEEL STATIC ADJUSTING THE HEADLIGHT BEAM
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 |

©2015- 2017 megalektsii.ru Права всех материалов защищены законодательством РФ.